LG DFB425FP User Manual download pdf (Page 17)

To prevent siphoning, one of the following

methods must be used.

Method 1

When the drain hose is connected to a waste

spigot, the hose must be looped up to the

underside of the bench top and secured.

300 mm Min.

770 mm – 1000 mm

Bench top

Method 2

When the drain hose is connected to a separate

standpipe, it is essential that an airtight

connection be made. If not, it can induce odors.

700 mm Min.

1000 mm Max.

300 mm Min.

Air Tight

Connection

Standpipe 40 mm diametre Min.

Connecting the Water Supply

Hose

Connect the water supply hose to the water tap.

Water tap

Water supply hose

WARNING

• Do not shorten or damage the water supply

hose as it contains electrical wires and

components. It can not be detached or

removed from the appliance for installation

purposes.

• It is important that the water supply hose not

be tampered with, cut, disassembled, pulled,

or kinked. It contains electrical wiring inside

and if damaged, can cause an electrical

hazard.

CAUTION

• This appliance may be fed with either hot or

cold water. If the water connection can not be

maintained below 65ºC, the appliance must be

connected to cold water.

• Use sealant tape or sealing compound on the

tap's thread to avoid water leaks.

• Make sure that the line is not kinked or

sharply bent.

NOTE

• Before connecting the water supply hose to

the tap, turn on the tap to flush out foreign

substances (dirt, sand or sawdust) in the

water lines. Let water drain into a bucket.

• It takes about 3 – 4 minitues for the first

supply water.

Preparing Electrical Wiring

Connect the appliance to an earthed socket in

accordance with the current wiring regulations,

protected by a minimum 15 amp circuit breaker

or time delay fuse.

Wiring must be two wires with earth.

The power cord should not be positioned

behind the appliance but within 1.2 meters of

the side so that the plug is easily accessible.

WARNING

• For personal safety, remove house fuse or

open circuit breaker or switch off power plug

before installation.

• Do not use an extension cord or double

adapter.

• The plug must be plugged into an appropriate

outlet that is properly installed and grounded

in accordance with all local codes and

ordinances.

• Repairs to the appliance must only be carried

out by qualified service personnel. Repairs

carried out by inexperienced persons may

cause injury or serious malfunctioning.

Contact our local service centre.

• Connect to a properly rated, protected, and

sized power circuit to avoid electrical overload.

Final Check

Turn on electrical power.

Turn on house water supply.

The door should open and close smoothly

and without harsh noises, if the unit has

been leveled correctly.

Run the appliance on a Rinse cycle to verify

proper operation and check for leaks.

Error Code Possible Cause and Solution

OE Error

Drain hose kinked or pinched.

Feed the drainage and supply

hoses through the hole under the

sink. Then gradually slide the

dishwasher into the cabinet while

pulling on the hoses under the

sink to take up any slack. This

helps avoid kinking the hoses or

trapping them beneath the

dishwasher.

Waste spigot under sink is

clogged.

Drill out the waste spigot under

the sink.

IE Error

Water supply line kinked under

dishwasher.

Feed the drainage and supply

hoses through the hole under the

sink. Then gradually slide the

dishwasher into the cabinet while

pulling on the hoses under the

sink to take up any slack. This

helps avoid kinking the hoses or

trapping them beneath the

dishwasher.

House water supply not turned

on.

Turn water on. Water pressure

may be too high or too low.

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 55 56

Comments to this Manuals

No comments

LG DFB425FP User Manual Page 17

Comments to this Manuals

Related products and manuals for Dishwashers LG DFB425FP