LG F1403FDS User Manual download pdf

noituloSesuaC elbissoPmotpmyS

• Water supply is not adequate in area

• Water supply taps are not completely open.

• Water inlet hose(s) are kinked.

• The filter of the inlet hose(s) are clogged.

• Drain hose is kinked or clogged.

• The drain filter is clogged.

• Load is too small.

• Load is out of balance.

• The appliance has an unbalance detection

and correction system. If individual heavy

articles are loaded (ex. bath mat, both robe,

etc.), this system may stop spinning or even

interrupt the spin cycle altogether.

• If the laundry is still too wet at the end of the

cycle, add smaller articles of laundry to

balance the load and repeat the spin cycle.

• Is the door opened or not

completely closed?

• Water overfills due to the faulty water

valve.

• Water level sensor has malfunctioned.

• Over load in motor.

• Water leaks

• The washer experienced a power failure.

Check another tap in the house.

Fully open tap.

Straighten hose(s).

Check the filter of the inlet hose(s).

Clean and straighten the drain hose.

Clean the drain filter.

For more detailed information,

please refer to “Cleaning the drain pump filter”

Add 1 or 2 similar items to help

balance the load.

Rearrange load to allow proper

spinning

Close the door completely.

If “ ”is not released, call for service.

Unplug the power plug and call for service.

Close the water tap.

Unplug the power plug.

Call for service.

Restart the cycle.

arantiebedingungen

Unter die Garantie fallen nicht:

• Heimservice zur Einführung in die Benutzung des Geräts.

• Wenn das Gerät an eine Spannung angeschlossen ist, die nicht mit der auf dem

Nennleistungsschild angegebenen übereinstimmt.

• Wenn die Störung durch Unfälle, Vernachlässigung, Missbrauch oder höhere Gewalt

verursacht wird.

• Wenn die Störung durch unsachgemäße Benutzung des Geräts oder Nichtbeachtung

der Bedienungsanleitung verursacht wird.

• Die Gebrauchsanweisung für das Gerät zur Verfügung stellen oder die Einstellungen

des Geräts ändern.

• Wenn die Störung durch Schädlinge wie Ratten oder Kakerlaken etc. verursacht wird.

• Normale Geräusche oder Vibrationen z. B. das Geräusch von ablaufendem Wasser,

Drehgeräusche oder Pieptöne während der Erwärmung.

• Die Installation korrigieren, das Gerät nivellieren oder den Abfluss einstellen.

• Normale Wartung, wie sie im Benutzerhandbuch empfohlen wird.

• Entfernung von Fremdkörpern wie Sand, Nägeln, BH-Bügeln, Knöpfen etc. aus der

Maschine sowie aus der Pumpe und dem Einlassfilter.

•

Sicherungen ersetzen oder die elektrischen Anschlüsse oder Rohrleitungen korrigieren.

• Korrektur von unbefugten Reparaturen.

• Schäden an persönlichem Eigentum, die direkt oder indirekt durch Defekte dieses

Geräts verursacht werden.

•

Wenn dieses Gerät zu kommerziellen Zwecken benutzt wird, steht es nicht unter Garantie.

(Beispiel: öffentliche Orte wie Toiletten, Hotels, Fitness-Center, Pensionen)

Entsorgung von Altgeräten

1. Wenn dieses Symbol eines durchgestrichenen Abfalleimers

auf einem Produkt angebracht ist, unterliegt dieses Produkt

der europäischen Richtlinie 2002/96/EC.

2. Alle Elektro- und Elektronik-Altgeräte müssen getrennt vom

Hausmüll über dafür staatlich vorgesehenen Stellen entsorgt

werden.

3. Mit der ordnungsgemäßen Entsorgung des alten Geräts

vermeiden Sie Umweltschäden und eine Gefährdung der

persönlichen Gesundheit.

4. Weitere Informationen zur Entsorgung des alten Geräts

erhalten Sie bei der Stadtverwaltung, beim Entsorgungsamt

oder in dem Geschäft, wo Sie das Produkt erworben haben.

3 . Die 4 Schrauben lösen und die

Gummipfropfen etwas drehen, um sie

zusammen mit den Schrauben abzunehmen.

Die 4 Schrauben und den Schraubenschlüssel

für späteren Gebrauch aufbewahren.

• Die Transportsicherungsschrauben müssen vor

jedem Transport des Geräts wieder angebracht

werden.

4 . Die Schraubenbohrungen mit den

beiliegenden Kappen verschließen.

1 2

3 4

Schraubenschlüssel

Adjustable feet

60 - 100 cm

Green and

Yellow (Earth)

Brown(Live)

Blue(Neutral)

Fuse

Cord

grip

Green and Yellow(Earth)

Brown(Live)

Blue(Neutral)

Fuse

Cord

grip

Owner‘s Manual

F1403FDS(1~9)

WD-14988FDS

Safety instructions for use

Read all instructions and explanations of the installation before use. Follow the instructions carefully. Keep the operating

instructions handy for later use. If the appliance is sold or passed on then ensure that the new owner always receives these

operating instructions. The following warnings must be strictly observed for safety reasons. They must be read before instal-

ling the appliance and putting it into operation.

• Intended use: This appliance has been designed exclusively for use in dry-interior households. Use the appliance only with cold

drinking water and only for washing textiles with washing detergents designed for washing machines. Every other use is improper and

may lead to injuries, whereby the liability of the manufacturer will cease.

• This appliance may only be used by adults. Do not allow children to touch the controls or to play with the product.

• Never modify the appliance on your own, as this is dangerous.

• This appliance is heavy. Transporting with care.

• Remove all packaging and transport bolts before using the appliance. Otherwise serious damage may result.

• All installation work must be carried out by a qualiﬁed ﬁtter or technician.

• Have electrical connections done by a qualiﬁed electrician.

• Never place the appliance on the power cord.

• If the appliance is placed on a carpet then place the feet so that air can circulate underneath the appliance.

• Always unplug the machine and turn off the water supply after use. Disconnect appliance by pulling only the plug - never disconnect

by pulling the power cord. Never touch the plug with wet ﬁngers or hands.

• Do not overload the appliance.

• Wash only machine-washable textiles. If you have doubts regarding this, then observe the markings on the label.

• Never place electrical heaters, candles etc. in the vicinity of the appliance. They could cause the appliance to ignite or parts to warp.

• Protect the appliance from wet and damp. Otherwise, there is danger of electric shock and ﬁre.

• Connect the appliance to a suitable wall socket for 220-240V. Never use an extension cord or double adapter.

• Empty all pockets. Hard or sharp objects such as coins, needles, nails, screws or stones may cause serious damage.

Unbalanced mass may create heavy vibrations. If heavy vibrations remain also without load, call for an authorized customer service.

• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive substances

(such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.). This may result in ﬁre or explosion.

• Never insert products coated with mineral oils (e.g. nylon coating, plastic belts, etc. ) into the machine. If a stain remover has been

used then make sure that the solvent has been carefully washed out before inserting the clothes into the appliance. Oil may remain in

the tub after a whole cycle resulting in ﬁre during drying. So, do not load oily clothes.

• Do not operate the appliance at locations where ﬂammable substances are present such as oil, benzene or highly inﬂammable gas.

Such materials may cause ﬁre or explosion. Never use combustible detergents.

• Only add the prescribed amount of softener. Excessive amounts may damage the clothes.

• After washing, keep the drum door open to protect the door seal.

• Make sure that all water has run off before opening the door. Never open the door if water still remains. Danger of scalding.

• Animals and children may get into the washing machine. So always check the appliance before using it.

• During washing, the glass door becomes very hot. Keep children away from the appliance when in operation.

• Never try to repair the machine yourself. Incorrect repairs may result in injuries and/or serious defects to the machine.

• The product should be serviced and repaired only by the authorised customer service using original replacement parts.

• When disposing of your old machine, the power cable must be capped and the door lock must be made unusable in order to protect children.

• When placing on a carpeted ﬂoor, make sure that the opening in the socket is not blocked.

• If the appliance has been under water then contact the customer service. There is danger of electric shock and ﬁre.

• The cover cup of the ﬁlter as well as the dispenser drawer may not be opened during the operation.

• Keep all washing powder and detergents away from children. Danger of poisoning

Disposal

Before use please read carefully the safety instructions!

Thank you for buying an LG fully automatic washing machine.

Please read this owner‘s manual carefully, it provides instructions on safe installation, use and maintenance.

Keep it handy for future reference of this machine. Make a note of the model and serial numbers of your washing machine.

Remove Packaging

Requirements for installation site

Transit bolts

Electrical connection

Connecting water supply hose

• The appliance is ﬁtted with transit bolts to prevent internal

damage during transport. Be careful, heavy load!

• Packing and all transit bolts must be removed before using

the washing machine.

• When unpacking the base, be sure to remove the additional

packing support in the middle of the base packing.

Store original packing for future move.

Dispose of packing material according to local regulations.

Unscrew the 4 bolts

using the spanner

supplied.

Keep the 4 bolts and the spanner for the future use. Reﬁt transit bolts before transporting the appliance.

Level ﬂoor: Permissible ﬂoor gradient under entire washing machine

is 1˚ .

Power socket: Must be within 100 cm of either side of location of

washing machine. Do not overload the socket with more than one

appliance.

Additional Clearance: For wall, ﬂoor and door space is needed.

(10cm: rear / 2cm:right & left side). Do not place or store laundry pro-

ducts on top of the washing machine at any times. They can damage

the ﬁnish or controls of the machine.

1. Do not use an extension cord or double adapter.

2. Have damaged supply cords replaced by the manufacturer or its service agents or a similarly qualiﬁed person

to prevent danger.

3. Always unplug the machine and turn off the water supply after use.

4. Connect the machine to an earthed socket in accordance with current wiring regulations.

5. The appliance must be positioned so that the plug is easily accessible.

• Repairs to the washing machine must only be carried out by qualiﬁed personnel. Repairs carried out by inexpe -

rienced persons may cause injury or serious malfunctioning. Contact your local service centre.

• Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst

under pressure. The electronic control unit may become unreliable at temperatures below freezing point.

• If the appliance is delivered in the winter months and temperatures are below freezing: Leave the washing machine

standing at room temperature for a few hours before putting it into operation.

• Two rubber seals are supplied with the water inlet

hoses. They are used for preventing water leaks.

• Make sure the connection to taps is tight enough.

• Periodically check the condition of the hose and

replace the hose if necessary.

• Make sure that there is no kink on the hose and

that it is not crushed.

When your washing machine has two valves:

• The inlet hose with the red connector is for the hot

water tap.

• If the washing machine has two valves, power

saving is achieved through using hot valve.

Water supply pressure must be between 1.0-10 bar (100kPa~1000kPa)

Don’t strip or crossthread when connecting inlet hose to the valve.

If the water supply pressure is more than 1000kPa, a decompression

device should be installed.

• The drain hose should not be placed higher than 100 cm above the ﬂoor.

• Proper securing of the drain hose will protect the ﬂoor from damage due to any water leakage.

• If the drain hose is too long do not force back into the washing machine. This will cause unusual noise.

• Proper level-adjustment of the washing ma-

chine prevents excessive noise and vibration.

Install the appliance on a solid and level ﬂoor

surface, preferably in a corner of the room.

• If the ﬂoor is uneven, adjust feet as required.

(Do not insert pieces of wood etc. under the

feet). Make sure that all four feet are stable

and resting on the ﬂoor. Then check that

the appliance is perfectly level. (Use a spirit

level).

Safety instuctions for the installation

Install or store appliance where it will not be exposed to sub-zero temperatures or exposed to the weather. Fit ground of the

washing machine correctly to conform with all statutory regulations and ordinances. Ensure that the base opening is free from

obstruction by carpeting if the washing machine is installed on a carpeted ﬂoor. In countries where there is a risk of cockroach

infestation or other vermin, pay particular attention to keep the appliance and its surroundings in a clean condition at all times.

Any damage which may be caused by cockroaches or other vermin is not covered by the appliance guarantee.

CAUTION about positioning the appliance

Install the washing machine on a ﬂat hard ﬂoor. Make sure that air circulation around the washing machine is

not impeded by carpets, rug etc.

•

Never try to correct any unevenness in the ﬂoor using pieces of wood, cardboard or similar materials under the washing machine.

•

If it is not possible to position the washing machine away from a gas cooker or coal burning stove, an insulation panel

(85x60cm) covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two appliances.

•

The washing machine must not be installed in rooms where the temperature may drop below 0°C.

•

Please ensure that when the washing machine is installed an engineer can gain easy access in the event of a breakdown.

•

Adjust all four feet using the transit bolt spanner provided to ensure that the appliance is stable, with 20mm clearnace between

the top of the washing machine and underside of the worktop.

CAUTION about the power cord

We recommend connecting most appliances to a dedicated circuit. That is, a single outlet supplying power only to the appliance

concerned, without any additional outlets or branch circuits. Check the speciﬁcations of this owner‘s manual. Do not overload

wall sockets. Overloaded wall sockets, loose or damaged wall sockets or extension cords, frayed power cords, damaged or

cracked wire insulation are dangerous. Any of these conditions could result in electric shock or ﬁre. Periodically examine the

cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance,

and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or

mechanical abuse, such as being twisted, kinked, pinched, squashed in a jamb of a door, or walked upon. Pay particular atten -

tion to plugs, wall outlets, and the point where the cord exits the appliance. We recommend to use a residual current operated

device in the mains supply.

CAUTION about location and moving

This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stop -

cock if the machine is to be left for any length of time (e.g. if you are going on holiday), especially if there is no ﬂoor drain (gully)

in the immediate vicinity. If relocating the appliance use the original packing material. Disable the door lock to prevent young

children becoming trapped inside. Packaging material (e.g. plastic ﬁlm, Styrofoam) can be dangerous for children. There is a risk

of suffocation! Keep all packaging well away from children.

CAUTION about the ﬂoor surface

• The installation surface must be clean, dry and level.

• Install washing machine on a ﬂat hard ﬂoor.

• Proper placement and levelling of the washing machine ensure long, regular and reliable operation.

• The washing machine must be perfectly level and ﬁrmly in position.

• It must not “see-saw” across corners under load.

• The installation surface must be clean, free from ﬂoor wax and other lubricant coatings.

• Do not allow the feet of the washing machine to get wet. If feet of the washing machine get wet, slipping may occur.

Name of product Front loading washing machine

Power supply 220-240 V~, 50 Hz

Size WxDxH mm: 600 x 640 x 850

Weight 65 kg

Max. Watt

2100 W (Wash) / 1100 W (Steam)

Wash capacity 9 kg

Water consumption 59 l (6.5l / kg)

Permissible water pressure 1.0-10 bar (100-1000kPa)

Rattling and clanking noise Extraneous objects such as coins or safety pins maybe in drum or pump.

Thumping sound Heavy wash loads may produce a thumping sound. This is usually normal.

Vibrating noise Have all transit bolts and packing been removed?

Water leaks. Check and tighten hose connections. Unclog drain pipe.

Contact plumber if necessary.

Excessive suds Too much detergent or unsuitable detergent.

Washing machine does not start Power cord may not be plugged in or connection may be loose.

Washing machine won’t spin Check that the door is ﬁrmly shut.

Door does not open Once started, the door can not be opened for safety reasons.

Wait one or two minutes before opening the door to allow the electric

locking mechanism time to release.

Troubleshooting

Level adjustment

To prevent internal dama-

ge during transport, the

special 4 bolts are locked.

If they are not removed, it

may cause heavy vibrati-

on, noise and machine to

malfunction.

Installation of drain hose

Technical Speciﬁcation

If after completing connection water leaks from the hose, repeat the same steps. Use the most conventional

type of tap for water supply. In case the faucet is square or too big, remove the spacing ring before inserting

the tap into the adaptor.

BS Plug Safety Details (For U.K. User)

This appliance must be earthed As the colours of the wires in the mains lead

of this apparatus may not correspond with the coloured markings identifying

the terminals in your plug, proceed as follows: The green and yellow wire must

be connected to the terminal in the plug marked E or by the earth symbol or

coloured green or green and yellow. The wire coloured blue must be connected

to the terminal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal

marked with the letter L or coloured red. If a 13 amp (BS 1363) plug is used, ﬁt a 13 amp BS 1362 fuse.

For the U.K. customer

CUSTOMER SERVICES Tel. : 0870 - 873 - LGLG (5454) Fax. : 0870 - 872 - 7337

LGEUK SERVICE WEB-SITE : http://uk.lge.com

• When this crossed-out wheeled bin symbol is attached to a product it means the product is covered

by European Directive 2002/96/EC.

• All electrical and electronic products should be disposed of separately from municipal waste stream

via designated collection facilities appointed by the government or the local authorities.

• The correct disposal of your old appliance will help prevent potential adverse consequences for the

environment and human health.

• For more detailed information about disposal of your old appliance, please contact your city ofﬁce,

waste disposal service or the shop where you purchased the product.

The hose supplied with the machine must be used. Old hoses may not be reused

Close the holes with

the caps supplied.

Remove the 4 bolts

along with the rubber

bungs by slightly

twisting the bung.

P/No. :MFL38868794

1 2

Summary of Contents

Page 1 - WD-14988FDS

noituloSesuaC elbissoPmotpmyS• Water supply is not adequate in area• Water supply taps are not completely open.• Water inlet hose(s) are kinked.• The

Page 2 - 3. Intensive

123ACBABC1 2 3 4 51 3ProgramFabric TypeWater Temp.(Option)CottonLightly soiled clothing and small loads40°C (Cold, 30°C, 60°C)Cotton, underwear, pillo

LG F1403FDS User Manual

Browse online or download User Manual for Washing machines LG F1403FDS. LG F1403FDS Owner’s Manual

Summary of Contents

More documents for Washing machines LG F1403FDS

Comments to this Manuals

LG F1403FDS User Manual

Browse online or download User Manual for Washing machines LG F1403FDS. LG F1403FDS Owner’s Manual

Summary of Contents

More documents for Washing machines LG F1403FDS

Comments to this Manuals

Related products and manuals for Washing machines LG F1403FDS