LG WD-10467BD User Manual

Commercial WasherOperating InstructionsWD-10467BDPlease read this manual carefully. It providesinstructions on safe installation, use, and maintenance

10Part 5 PROGRAMMING MODEPress ButtonMEDICAL 90 NORMAL 75NORMAL 60STARTDescriptionMove to upper level orComes back to Idle StateMove to the mode in t

11Part 5 PROGRAMMING MODE• Do not use , .• It is only used in inspecting the machine. Note1. The method of entering set

12Part 5 PROGRAMMING MODE - Setup Mode• Special price days apply or not• Clear escrow enable or not (coin type only)• Add super wash apply or not • Se

13Part 5 PROGRAMMING MODE - Setup Mode22Pre-wash set upEntering set up mode.You will see LqC1Button DisplayOne or the other willdisplay. • toFF (top

14Part 5 PROGRAMMING MODE - Setup Mode33Washing time set upEntering set up mode.You will see LqC1Button DisplayPress the MEDICAL 90 button.Press the N

15Part 5 PROGRAMMING MODE - Setup Mode44Rinsing times per cycleEntering set up mode.You will see LqC1Button DisplayPress the MEDICAL 90 button.Press t

16Part 5 PROGRAMMING MODE - Setup Mode55Rinsing time setupEntering set up mode.You will see LqC1Button DisplayPress the MEDICAL 90 button.Press the NO

17Part 5 PROGRAMMING MODE - Setup Mode66Top spin speed – final spin time depends on RPM Entering set up mode.You will see LqC1Button DisplayTop spin s

18Part 5 PROGRAMMING MODE - Setup Mode77How to change the water levelYou can change the water level by selecting two options.1. LO indicate water lev

19Part 5 PROGRAMMING MODE - Test ModeData NameEntering the test mode1. Entering programming mode 2. MEDICAL 903. STARTPush and hold the MEDICAL 90 and

2PRODUCT FEATURESCONTENTS Direct Drive SystemThe advanced Brushless DC motor directly drives the drum without using a belt and pulley. Tilted Drum a

20Part 5 PROGRAMMING MODE - Test Mode22Factory reset - EEPt After factory reset, machine information is changed to the default value.Entering set up

21Part 5 PROGRAMMING MODE - Test Mode33Time set upEntering set up mode.You will see LqC1Press the NORMAL 75 or the NORMAL 60 button untilappears in th

22Part 5 PROGRAMMING MODE - Test Mode44Cycle Kill Noncoin TYPEPress MEDICAL 90button with NORMAL60 button, then press NORMAL 75button 3 times, press

23Part 6 ERROR MODE• Water supply is not adequate inarea.• Water supply taps are notcompletely open.• Water inlet hose is bent.• The filter of the inl

24Part 7 POWER FAIL RECOVERY In case of power failure, the machine stops running but the time display remains on, showing the time just beforepower fa

MEMO

MEMO

MEMO

P/ No.:MFL31245184

3Part 1 IMPORTANT SAFETY INSTRUCTIONSREAD ALL INSTRUCTIONS BEFORE USEWARNINGFor your safety, the information in this manual must be followed to minimi

4Part 1 IMPORTANT SAFETY INSTRUCTIONSREAD ALL INSTRUCTIONS BEFORE USESAFETY INSTRUCTION FOR INSTALLATIONWARNING For your safety, the information in th

5Part 1 IMPORTANT SAFETY INSTRUCTIONSREAD ALL INSTRUCTIONS BEFORE USESAFETY INSTRUCTION FOR SAFETY USE/CLEANING/CARE/DISCARDWARNING For your safety, t

6Part 2 SPECIFICATIONS Accessories Name: Front-loading Washing Machine Power supply: 220V~ 50Hz Size: 68.6 cm (W) X 75.6 cm (D) X 98.3 cm (H), 129.1

7Part 3 IDENTIFICATION WD-10467BD1. DISPLAY LED2. CYCLE BUTTON3. START BUTTON4. STATUS LED5. CYCLE LED1 25 4 3

8Part 3 IDENTIFICATIONThe START LED flashes when the full vend pricehas been satisfied then the cycle has been chosen.33START BUTTON• LED flashes whe

9Part 4 OPERATING YOUR WASHERThe cycle LEDs is lit at the same time, and displayed‘PUSH’.11Ready modePress the desired button and press the start butt