OWNER’S MANUALWASHING MACHINE WD13020DWD13020D1WD12020DP/No.: MFL59755518www.lg.comBefore beginning installation, read these instructions carefully. T
10nstallationILevel adjustment Concrete floors Wooden floors (Suspended floors)1. Adjusting the washing machine level properly prevents excessiven
11are before washingC1. Care LabelsLook for a care label on your clothes. This will tell you about the fabric content of your garment andhow it should
12dding detergentA• Main wash only ➔• Pre Wash + Main Wash ➔• Do not exceed the maximum fill line.Close the dispenser drawer slowly.Overfilling can ca
13dding detergentA• The detergent should be used according to theinstruction of the detergent manufacture.• If too much detergent is used, too many su
14unctionFRecommended courses according to the laundry type❋ Water Temperature : Select the water temperature to the wash cycles.Always follow garmen
15ow to use washerH• Press the Power button to start.• Press the Start/Pause button.• Initial conditions- Wash : main wash- Rinse : 3 times- Spin :• 1
16ow to use washerH(1) Dial : Program(2) Button : Start / Pause(3) Button : Spin(4) Button : Temperature(5) Button : Power(6) Button : Medic Rinse(7)
17ow to use washerHStart/PauseDetecting• This Start/Pause button is used to startwash cycle or pause the wash cycle.• If temporary stop of wash cycle
18ow to use washerHChild LockIf you choose to lock the buttons on the controlassembly to prevent tampering this functionmay be selected.• Child Lock c
19ow to use washerHSpin[WD13020D/WD13020D1][WD12020D]2. No spin3. Rinse Hold• Rinse Hold is selected by pressing thespin button repeatedly this functi
2roduct FeaturesPontentsCWarnings...3Specifications...
20ow to use washerHWater Temp.• By pressing the Temp.button, the watertemperature can beselected.- Cold- 30˚C / 40˚C / 60˚C / 95˚C• Water temperature
21• If the machine encounters a fault duringoperation, the associated fault will bedisplayed.“ ” : Water pressure sensing error“ ” : Probl
22aintenanceM The water inlet filter- " " error message will blink on the control panel when water does not enter thedetergent dr
23aintenanceM32321100 The drain pump filter❋ The drain filter collects threads and small objects left in the laundry.Check regularly that the filter
24aintenanceM Dispenser drawer❋ After a while detergents and fabric softeners leave a deposit in the drawer.• It should be cleaned from time to time w
25aintenanceM Cleaning your washer1. ExteriorProper care of your washer can extend its life.The outside of the machine can be cleaned with warm water
26roubleshooting guide❋ This washing machine is equipped with automatic safety functions which detect and diagnose faults at anearly stage and react a
27Washer does not startWasher will not spinDoor does not openWash cycle timedelayed• Electrical power cord may notbe plugged in or connectionmay be lo
28roubleshooting guideSymptom Possible Cause SolutionT• Water supply is not adequate in area.• Water supply taps are not completely open.• Water inlet
3arningsWFor your safety, the information in this manual must be followed to minimizethe risk of fire or explosion, electric shock, or to prevent prop
4pecificationsSSpannerInlet hose(2EA) Accessories Name : Front loading washing machine Power supply : 220-240V~,50Hz Size : 600mm(W)550mm(D) 850
5nstallationI1. To prevent internal damage duringtransport, the special 4 bolts are locked.Before operating the washer, remove the bolts along with th
6nstallationILaundryTubWasherapprox.2cmDrain HoseInstallation place requirementPositioningInstall the washer on a flat hard floor. Timber base and s
7nstallationIHot water tapColdHotCold water tap▶Water supply pressure must be between 100kPa and 100-800kpa (1-8 bar) ▶Don’t strip or crossthread wh
8nstallationINormal Tap without thread & screw type inlet hoseNormal Tap without thread & one touch type inlet hose (Single inlet models)1.
9nstallationIThis equipment is not designed for maritime use or for use mobile installations such ascaravans, aircraft etc.Turn off the supply tap if
Comments to this Manuals