OWNER’S MANUALCOMMERCIAL WASHERMODELF1069FD2S/F1069FD3Swww.lg.comBefore beginning installation, read these instructions carefully. This will simplifyi
10INTRODUCING YOUR WASHING MACHINE Start buttonDisplay LEDStatus LED Cycle buttonDisplay LEDThe display shows the vend price and remaining time and pr
11INSTALLATION INSTRUCTIONSSpace requirements You must allow sufficient space for water lines, the drain line, and airflow.Installing on a floorInstal
12INSTALLATION INSTRUCTIONSFoam Tub Support Carton Base NOTE• Save the bolt assemblies for future use. To prevent damage to internal components, DO N
13INSTALLATION INSTRUCTIONS NOTE• For your safety, and for extended product life, use only authorized components. The manufacturer is not re-sponsibl
14INSTALLATION INSTRUCTIONSConnecting the drain lineSecure the drain hose in place to prevent moving and leaking.Using a standpipe 1 Clip the end of
15INSTALLATION INSTRUCTIONSLeveling the washing machine The washer tub of your new washing machine spins at very high speeds. To minimize vibration, n
16PREPARATIONCheck all pockets to make sure that they are empty. u-Items such as clips, matches, pens, coins, and keys can damage both your washer an
17PREPARATIONCategory Label DirectionsWashingHand Wash Machine Wash, Normal Cycle Use Permanent Press/Wrinkle Resistant washing machine setting (whic
18PREPARATION NOTE• It is normal for a small amount of water to remain in the dispenser compartments at the end of the cycle.About the dispenserThe a
19OPERATING YOUR WASHEROPERATING YOUR WASHER ❋ Do not work any button and stop the washer (When the washer is operating) or (when a cycle is in prog
2PRODUCT FEATURESPRODUCT FEATURESDIRECT DRIVE SYSTEMThe advanced Brushless DC motor directly drives the drum without using a belt and pulley.TILTED DR
20PROGRAMMING MODE- OPL type -How to enter "Programming mode"You can enter programming mode only for Idle state and pause state.- OPL Type1)
21PROGRAMMING MODEOPL typeAlgorithm flow chart shows how to control programming mode.Before program set, check the structure of programming mode.The
22PROGRAMMING MODE - SETUP MODESetup Mode : (display)You can change washer vend price, cycle time, and cycle parameters, etc.Entering set up
23PROGRAMMING MODE - SETUP MODE NOTE• In case of OPL type, (Pre-wash) is only available in .• Special price days apply or not• Disabled•
24Programming mode - setuP modeEntering set up mode.You will see LqC1Button DisplayPress the 90°C MEDICAL button.Press the 75°C HOT or the 60°C NORMAL
25PROGRAMMING MODE - SETUP MODEEntering set up mode.You will see LqC1Button DisplayPress the 90°C MEDICAL button.Press the 75°C HOT or the 60°C NORMAL
26PROGRAMMING MODE - SETUP MODEEntering set up mode.You will see LqC1Button DisplayPress the 90°C MEDICAL button.Press the 75°C HOT or the 60°C NORMAL
27PROGRAMMING MODE - SETUP MODEEntering set up mode.You will see LqC1Button DisplayPress the 90°C MEDICAL button.Press the 75°C HOT or the 60°C NORMAL
28PROGRAMMING MODE - SETUP MODEEntering set up mode.You will see LqC1Button DisplayPress the 90°C MEDICAL button.Press the 75°C HOT or the 60°C NORMAL
29PROGRAMMING MODE - SETUP MODE NOTE• This function is only controlled in machine. (It is not applied in setup card.)Entering set up mode.You will se
3IMPORTANT SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONSREAD ALL INSTRUCTIONS BEFORE USE WARNING For your safety, the information in this manual mu
30PROGRAMMING MODE - SETUP MODEEntering set up mode.You will see LqC1Button DisplayPress the 90°C MEDICAL button.Press the 75°C HOT or the 60°C NORMAL
31PROGRAMMING MODE - SETUP MODEEntering set up mode.You will see LqC1Button DisplayPress the 90°C MEDICAL button.Press the 75°C HOT or the 60°C NORMAL
32PROGRAMMING MODE - TEST MODEPROGRAMMING MODE - TEST MODEDiagnostic tests: (display)This program has been added for testing the washer and
33PROGRAMMING MODE - TEST MODE NOTE• Washing time 0 minutes• Rinse cycle twice• Top spin speed
34PROGRAMMING MODE - TEST MODEEntering set up mode.You will see LqC1Button DisplayPress the 75°C HOT or the 60°C NORMAL button until
35PROGRAMMING MODE - TEST MODEEntering set up mode.You will see LqC1Button DisplayPress the 75°C HOT or the 60°C NORMAL button until
36PROGRAMMING MODE - TEST MODE NOTE• Default password is 1. If you want to change the password, you should know the present password.Entering set u
37PROGRAMMING MODE - TEST MODEEntering set up mode.You will see LqC1Button DisplayPress the 75°C HOT or the 60°C NORMAL button until
38MAINTENANCEAfter the cycle is finished, wipe the door and the inside ofthe door seal to remove any moisture. Leave the door opento dry the washer tu
39MAINTENANCE WARNING• Unplug the power cord and turn off the faucets before cleaning. Failure to do so may cause electric shock.• Do not use the wa
4IMPORTANT SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONSREAD ALL INSTRUCTIONS BEFORE USE WARNING For your safety, the information in this manual mu
40MAINTENANCECleaning the drain pump filterThe washing machine fails to drain if the drain pump filter is clogged. Periodically clean the drain filter
41MAINTENANCE CAUTION• Cleaning the door seal with an undiluted solution may cause malfunction of the door seal and washing ma-chine parts.Clean the
42ERROR MODEERROR MODEMeaning of Error Codes that LED displays during occurrence of problem.Problem Possible Cause Solution• Water supply is not ade
43POWER FAIL RECOVERY & DEFAULT WASHER SETTINGS & SPECIFICATIONSPOWER FAIL RECOVERY In case of power failure, the machine stops running but th
OWNER’S MANUALCOMMERCIAL WASHERMODELF1069FD3Swww.lg.comBefore beginning installation, read these instructions carefully. This will simplifyinstallatio
5IMPORTANT SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONSREAD ALL INSTRUCTIONS BEFORE USE WARNING For your safety, the information in this manual m
6IMPORTANT SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONSREAD ALL INSTRUCTIONS BEFORE USE WARNING For your safety, the information in this manual m
7TABLE OF CONTENTSTABLE OF CONTENTS 2 PRODUCT FEATURES3 IMPORTANT SAFETY INSTRUCTIONS4 BASIC SAFETY PRECAUTIONS4 GROUNDING INSTRUCTIONS 5 SAFETY
8INTRODUCING YOUR WASHING MACHINE INTRODUCING YOUR WASHING MACHINEParts and AccessoriesPartsAccessoriesDetergent dispenser drawerDoorMagnet Door Plung
9INTRODUCING YOUR WASHING MACHINE 1. Display LED2. Cycle button3. Optional cycle button4. Start button5. Status LEDControl panel features1 254 31 254
Comments to this Manuals