LG LND5100 User Manual download pdf (Page 2)

Precautions

• Be sure to switch off the unit before

installation and connection.

• The installation should be made by

qualified service personnel or system

installers.

• Do not expose the power and

connection cables to moisture, which

may cause damage to the unit.

Connecting Network

You can control and monitor the system

via network. With the remote control

(monitoring), you can change the system

configuration or monitor the image via

network. After the installation, check the

network settings for the remote control and

monitoring work.

Connect the IP camera to your network using

a standard RJ-45 network cable as shown

below.

ETHERNET

With PoE

Broadband

Service

Broadband

Service

PoE Device

(IEEE802.3af )

Router

Connecting Power Source

Connect power, using one of the methods

listed below:

To use the power adapter

Connect a DC 12 V power source to the

power input terminal as shown below.

(recommended power adapter is DC 12 V/1.5

A or above)

POWER IN

DC 12 V

ETHERNET

With PoE

NOTE:

When the connecting Alarm and Audio,

tighten the screws as shown above.

To use the PoE (Power over Ethernet)

device

Connect the PoE cable to the LAN port on the

unit. You must use the “IEEE802.3af” standard

PoE device.

POWER IN

DC 12 V

ETHERNET

With PoE

PoE Device

(IEEE802.3af )

NOTE:

If the camera doesn’t work properly after

connecting PoE device, please check if the

PoE device supplies enough power.

Connecting Alarm Device

Alarm terminals are used to connect the

alarm (relay) devices such as sensors, door

switches, etc.

ALARM IN / ALARM IN RETURN (Sensor

Input)

Connect the sensor device to the sensor input

terminal.

Sensor Device

BLACK

GREEN

GREEN-ALARM IN

BLACK-ALARM IN

RETURN

RED-ALARM OUT

WHITE-ALARM

OUT

RETURN

ALARM OUT / ALARM OUT RETURN (Relay

Output)

Connect the alarm (relay) device to the relay

output terminal. Alarm signal is outputted at

an event occurrence.

Alarm (relay)

Device

WHITE

RED

GREEN-ALARM IN

BLACK-ALARM IN

RETURN

RED-ALARM OUT

WHITE-ALARM

OUT

RETURN

NOTE:

The Photo MOS Relay is rated for 100 mA at

20 V DC or 100 mA at 28 V AC.

Connecting Microphone

and Speaker Device

Optionally connect an active speaker and/or

external microphone with a built-in amplifier.

AUDIO OUT

AUDIO IN

NOTE:

Keep the microphone away from the speaker

to avoid howling.

Using the micro SD card

You can record your surveillance environment

with the micro SD card even if the network is

disconnected condition.

To insert the micro SD card

1. Remove the Dome Cover.

2. Insert the micro SD card carefully as

shown in the following illustrations.

Make sure the micro SD card terminal

position before insert the micro SD card.

Push the back end of the micro SD card

to fix it at the last step.

NOTES:

• Do not use the power too much when

you insert the micro SD card. The micro

SD card may be damaged.

• If you insert the micro SD card in the

wrong position, the micro SD card

may be damaged or it may cause the

malfunction of the micro SD Card Slot.

• Keep the terminal part of the micro SD

card in clean. Be careful the terminal part

of the micro SD card not to dusty.

• As the micro SD card is consumable, the

micro SD card end its days and may be

not able to save data if you use it more

than over certain times. In this case,

replace micro SD card to buy a new one.

Remove the micro SD card

1. Press the back end of the micro SD card

to release the lock condition.

2. Take the micro SD card out carefully from

the camera. It may cause a malfunction

of the micro SD card or the micro SD

card slot if you use the power too much

at lock status.

CAUTION:

• If you install the micro SD card on the

camera and remove with the micro SD

card condition indicator lights on, you

must unmount the micro SD card by

using the [System > Storage > Device

Management > Unmount] menu. The

micro SD card data is compromised or

the camera may not operate normally,

if you remove the card without use

[Unmount] function.

• LG Electronics is not responsible for

deleted data caused by user mishandling

when you insert or remove the micro

SD card.

Recommended the micro SD card

specification

Maker Capacity

Block Size

(FAT 32)

Less than

32 GB

32 kbyteSandisk

Transcend

NOTE:

Speed of reading and writing more than

10 MB/Sec. (Class 6)

Connection

Follow the instructions below to install the camera with camera mounting bracket.

1. Use the installation guide template to check the mounting location. Face the front of the

label toward the area of interest. Using the template as a guide, make a hole through the

ceiling.

CAUTION:

Install on a ceiling or wall where can withstand the weight of 5 times of the camera including

mounting bracket.

2. Install the camera mounting bracket to the ceiling.

3. Connect the cables to the cable jacks of the camera body.

4. Assemble the camera and mounting bracket after align the front part of the camera and

mounting bracket. Connect the unit by following step a and b.

FRONT

PRODUCT CENTER POSITION

MEZ62687703

SELFTAPPING SCREW

4 Place

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

100 Cutting Line

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

100 Cutting Line

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

NOTE:

To disassemble the camera from the mounting bracket, rotate the camera counterclockwise with

pressing the PUSH button inside the camera body.

Camera Adjustment

1. Connect the portable minitor to the video jack using the test monitor cable.

TILT

ROTATION

WIDE

TELE

NEAR

FAR

PA N

Test monitor cable

2. Adjust the pan/tilt/rotation position of the camera.

TILT

ROTATION

WIDE

TELE

NEAR

FAR

PA N

3. Adjust the zoom and focus.

TILT

ROTATION

WIDE

TELE

NEAR

FAR

PA N

Mounting the camera

1 2

Comments to this Manuals

No comments

LG LND5100 User Manual Page 2

Comments to this Manuals

Related products and manuals for Security cameras LG LND5100